install the gas check before or after the lube boolit?

Boolit Mold Join DateMar 2013Posts13

Traduzione
hello to everyone! I have only just begun to melt the balls. lube if you use a pan, I must first drawing and then put the gas chek and then put the bullets in the pan lube?

Ciao a tutti . Ho cominciato da poco a fondere i proiettili . Devo prima trafilere , poi mettere il gas check , poi alla fine metto i proiettili nel pan lube ?

Boolit Mold Join DateMar 2013Posts13

but to put the gas check I have to pass them in the lube Die , and to do this I must first GREASE, because without fat stick to die

Boolit Mold Join DateMar 2013Posts13

Traduzione
what I mean is: when I put the GC at the end of the bullets are already greased, why should I even pass them in the pan lube? sorry if my questions are stupid, I'm a newbie

Traduzione dall'inglese con babel

Non si far? male le pallottole per lubrificare il proiettile prima con il grasso e correre attraverso il dado dimensioni per installare il controllo del gas. ? possibile utilizzare ragia minerale per pulire il proiettile dopo aver installato il controllo del gas. Quindi, ? possibile utilizzare il pan di lubrificazione per lube i proiettili come ti piace.

It will not hurt the bullets to lubricate the bullet before grease and run it through the die size to install the gas check. You can use mineral spirits to clean the bullet after installing the gas check. You can then use the pan to lube the bullets as you like.

Stai usando grasso per lubrificare i proiettili, o stai usando un lubrificante della pallottola, come chiamati?

Are you using grease to lubricate the bullets, or are you using a bullet lubricant, such as alox?

I will fear no evil, for thou art with me.

I assume your talking about sizing with the Lee push through sizer to size then you pan lube & you don't want to stick a bullet in the Lee sizer.

Put your cast bullets in a container. I use a gallon ziploc bag. Spray about 2-3 pumps of Case Lube over the bullets. Shake to get an even coating. This will prevent sticking a bullet in the Lee sizer die when you size & install the GC. Pan lube as you like.

Hope this helps.

Boolit Master Join DateFeb 2007LocationmissouriPosts428

I've never has any problem pushing them thru a lee sizer without lube, unless they are linotype and way over sized.

I always install it before. That way I get a tight fit to the boolit lead before any lube can get underneath. I have this impression that lube under the gas check is what causes some of the gas checks to come off .... I can't prove that though ....
Ohio Rusty ><>

"This is America !!, where many have fought and died for our right
to celebrate our views with inflatable creatures in our yards ......."

If you ever decide to buy a Lyman or RCBS sizer/luber they sell a tool that sets on the stem that allows the bullet to have a GC installed but not lubed.
The best way if pan lubing is to spray the bullets with a sizing lube and apply the GC by running through a sizing die. The GC is a crimp on fit and not just a push on and load item. If not crimped by a die it will come off the bullet in firing and be useless.
The GC is always first. If using a Star sizer then you place a GC on the bullet and lube it all in one step. Very fast David

Shooter of the "HOLY BLACK" SASS 81802 AKA FAIRSHAKE; NRA ; BOLD; WARTHOG;Deadwood Marshal;Bayou Bounty Hunter; So That his place shall never be with those cold and timid souls who neither know victory nor defeat

You may not post new threadsYou may not post repliesYou may not post attachmentsYou may not edit your postsForum Rules

Abbreviations used in Reloading
Pointed Soft Point "Core Lokt"

View the original article here